[Bugme-new] [Bug 354] New: Kernel panic on boot after realtek RTL-8139 ethernet intialization
bugme-daemon at smtp.osdl.org
bugme-daemon at smtp.osdl.org
Fri Feb 14 01:02:57 PST 2003
http://bugme.osdl.org/show_bug.cgi?id=354
Summary: Kernel panic on boot after realtek RTL-8139 ethernet
intialization
Kernel Version: 2.5.60-mm1
Status: NEW
Severity: high
Owner: akpm at digeo.com
Submitter: nuclear at operamail.com
Distribution:gentoo linux
Hardware Environment:
/proc/cpuinfo
processor : 0
vendor_id : GenuineIntel
cpu family : 6
model : 8
model name : Pentium III (Coppermine)
stepping : 10
cpu MHz : 997.372
cache size : 256 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 mmx fxsr sse
bogomips : 1961.98
lspci -vvv :
00:00.0 Host bridge: VIA Technologies, Inc. VT8605 [ProSavage PM133]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at e3000000 (32-bit, prefetchable) [size=4M]
Capabilities: [a0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2,x4
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.0 PCI bridge: VIA Technologies, Inc. VT8605 [PM133 AGP] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: e0000000-e1ffffff
Prefetchable memory behind bridge: d0000000-d7ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40)
Subsystem: VIA Technologies, Inc. VT82C686/A PCI to ISA Bridge
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.1 IDE interface: VIA Technologies, Inc. VT82C586/B/686A/B PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc. VT8235 Bus Master ATA133/100/66/33 IDE
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at c000 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.2 USB Controller: VIA Technologies, Inc. USB (rev 1a) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at c400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.3 USB Controller: VIA Technologies, Inc. USB (rev 1a) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at c800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
Subsystem: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEV
Software Environment:
If some fields are empty or look unusual you may have an old version.
Compare to the current minimal requirements in Documentation/Changes.
Linux illuminus 2.4.20-gentoo-r1 #1 Fri Jan 17 12:23:56 GMT 2003 i686 Pentium III (Coppermine) GenuineIntel GNU/Linux
Gnu C 18:
Gnu make 3.80
util-linux 2.11u
mount 2.11u
module-init-tools 0.9.9
e2fsprogs 1.30
reiserfsprogs 3.6.3
Linux C Library 2.3.1
Dynamic linker (ldd) 2.3.1
Procps 2.0.10
Net-tools 1.60
Kbd 1.06
Sh-utils 2.0.15
Modules Loaded radeon sg sd_mod scsi_mod
gcc-3.2.1
Problem Description: reproducable error during boot right after ethernet
driver intialization.
I retypes the output on a separate machine, but I believe it is correct.
Hope all this is useful!
Kernel Output:
alloc_skb called nonautomically from interupt c02cdf63
------------[ cut here ]-------------
kernel BUG at net/core/skbuff.c:178!
invalid operand: 0000
CPU: 0
EIP: 0060:[<c02c30a6>] Not tainted
EFLAGS: 00010282
eax: 0000003a ebx: c03adba0 ecx: c036d954 edx: 00000001
esi: 000000d0 edi: 00000010 ebp: c13d6800 esp: c1299e48
ds: 007b es: 007b ss: 0068
Process swapper (pid: 1, threadinfo=c1298000 task=c12be040)
Stack: c035aa00 c02cdf63 c03adba0 ffffffff c02cdf63 00000f60 000000d0 c13f10e0
c1384500 00000000 c03ad5a0 c03adba0 c13d6800 00000005 c13d6800 c02ce1d5
00000010 c13d6800 ffffffff c0128afd c03adba0 00000005 c13d6800 c1298000
Call Trace: [<c02cdf63>] [<c02cdf63>] [<c02ce1d5>] [<c0128afd>] [<c02c8ccb>] [<c023e4e7>] [<c0241310>] [<c0241560>] [<c023f1cb>] [<c017d82e>] [<c017d885>] [<c01efc7e>] [<c0215fd5>] [<c02160fc>] [<c02163f0>] [<c02167cf>] [<c01efdbb>] [<c010507f>] [<c0105040>] [<c0107249>]
Code: 0f 0b b2 00 8a 9b 35 c0 e9 62 fe ff ff 8d b6 00 00 00 00 8d
<0>Kernel panic: Aiee, killing interrupt handler!
In interupt handler - not syncing
Steps to reproduce: boot the kernel.
------- You are receiving this mail because: -------
You are on the CC list for the bug, or are watching someone who is.
More information about the Bugme-new
mailing list